Six Factors That Control Metal Flow in Titanium Alloy Extrusion
Mar 13, 2024
Titanium billets are extruded at a thermal conductivity close to one tenth that of aluminium, so the heat generated by deformation and the heat supplied by the container never equalise across the section. That single physical fact explains why metal flow control in titanium extrusion is far more demanding than in copper, aluminium or even carbon steel.
Why Titanium Behaves Differently Inside the Extrusion Container
When a titanium rod or titanium alloy bar billet is pushed through a die, the skin and the core are almost never at the same temperature. With a container temperature of about 400 °C, the difference between the outer layer and the centre of the billet has been measured at 200 to 250 °C. Under that gradient the surface and the core carry very different strength and plasticity, so deformation is uneven: the slower core drags against the faster skin, extra tensile stress builds up in the surface layer, and the product can leave the die with cracks and seams already initiated.
The consequences are not cosmetic. Uneven flow leaves residual stress that appears later as bow, twist or out-of-round after machining. In tube extrusion it produces wall-thickness eccentricity that cold drawing alone cannot correct. A supplier able to hold tight concentricity on extruded titanium tube is really confirming that this gradient was managed, not ignored.
How the Phase State of the Billet Sets the Flow Pattern
Flow behaviour changes with the phase state of the alloy. Extruding inside the alpha or alpha+beta field gives a noticeably more uniform flow than extruding in the beta field, although beta extrusion offers lower flow stress and is sometimes the only way to reach a required reduction on a given press. That trade-off is settled before the billet reaches the press, because billet heating temperature is the variable that selects the phase.
Chemistry matters too. Unalloyed grades such as Grade 1 to Grade 4 and the near-alpha alloys behave differently from the alpha+beta Grade 5 (Ti-6Al-4V) family, and the beta alloys differ again. A press schedule written for one family should not be copied to another. ASTM B348 for bar and billet, and ASTM B338 and ASTM B861 for tube, fix the delivered chemistry, mechanical properties and testing, but leave the thermomechanical route to the producer, and that route is exactly where flow control lives.
The Six Factors, Ranked by Shop-Floor Impact
On a production press the variables reduce to six that a process engineer can actually act on.
| Factor | Effect on flow uniformity | Practical direction |
|---|---|---|
| Extrusion method | Reverse extrusion is more uniform than forward; cold more uniform than hot; lubricated more uniform than dry | Use a lubricated indirect route where the press allows it |
| Extrusion speed | Rising ram speed increases uneven flow and the temperature gradient | Cap speed on sections with tight wall eccentricity limits |
| Extrusion temperature | Higher billet temperature lowers deformation resistance but increases uneven flow | Extrude in the alpha or alpha+beta field when surface quality matters |
| Lubrication | Lubricants cut friction between billet and container and flatten the flow front | Never run dry; glass or graphite-based systems are usual for titanium |
| Die geometry | Entry angle and land length set dead-metal zones and back pressure | Match the die to the reduction rather than to a stock design |
| Billet condition | Surface scale, cast texture and soak time all shift the flow front | Machine or condition the billet before loading |
Die Wear and the Iron- and Nickel-Base Tooling Problem
Tooling is the second half of the story. At extrusion temperature titanium reacts with iron-base and nickel-base die materials at the contact surface and forms low-melting eutectics, which causes galling and fast die wear. This is the main reason titanium extrusion without lubrication is impractical on a commercial press. Dies therefore need generous land support, short inspection intervals and a lubricant film that survives the whole stroke.
The same reactivity means die, container liner and dummy block materials should be judged on compatibility with titanium rather than on hardness alone. A tool that performs well in stainless steel work can still scuff in titanium service.
Practical Starting Points for Rod and Tube Extrusion
| Product | Billet handling | Typical extrusion window | Flow control lever |
|---|---|---|---|
| Unalloyed titanium rod (Grade 1 to 4) | Machined, preheated under controlled atmosphere | Alpha-field extrusion at moderate ram speed | Parity of container and die preheat |
| Ti-6Al-4V rod (Grade 5) | Fully soaked through before loading | Alpha+beta or beta field, pressure-controlled start | Ram speed ramp at breakthrough |
| Seamless tube shell | Centred, lubricated billet | Lower speed than bar at equal reduction | Mandrel alignment and wall eccentricity monitoring |
These are shop-floor starting points, not specification limits. The controlling documents for the delivered product remain ASTM B348 for bar and billet and ASTM B338 and ASTM B861 for tube and pipe.
How Flow Uniformity Shows Up in the Finished Product
Uniform flow is visible long before the metallographic report. It shows up as consistent grain size from surface to centre after annealing, low residual bow after straightening, wall thickness concentric within a few tenths of a millimetre, and a clean pickled surface with no lap or seam indications. Where ultrasonic or eddy-current testing is part of the order, uniform flow keeps the rejection rate low because there are no flow-line defects for the probe to find.
For buyers, the useful question is not whether the press is large enough but how those six factors are controlled and recorded. A producer who can describe the billet soak, the lubricant, the ram-speed profile and the die maintenance interval is describing a stable process.
Frequently Asked Questions
Q: What is the single biggest factor affecting metal flow in titanium extrusion?
A: Billet temperature, because it selects the phase state of the alloy and therefore the flow stress and friction behaviour of the whole charge.
Q: Why is reverse extrusion more uniform than forward extrusion?
A: In reverse extrusion the billet does not slide along the container wall, so friction is largely removed and the flow front stays flat.
Q: Does a higher extrusion temperature always improve surface quality?
A: No. Higher temperature lowers deformation resistance but widens the temperature gradient and increases uneven flow, which promotes surface cracking in alpha+beta alloys.
Q: Why is lubrication mandatory for titanium but not always for steel?
A: Titanium reacts with iron-base and nickel-base die material at extrusion temperature to form low-melting eutectics, so dry contact causes galling and rapid die wear.
Q: Which standards define the delivered titanium bar or tube?
A: ASTM B348 covers titanium bar, billet and forging stock, while ASTM B338 and ASTM B861 cover seamless and welded tube and pipe; they fix chemistry and properties, not the extrusion schedule.







