ASTM B861 Grade 12 Titanium Tube (Ti-0.3Mo-0.8Ni): Specifications, Properties and Applications
Oct 22, 2025
What Is Grade 12 Titanium?
Grade 12 titanium, known as Ti-0.3Mo-0.8Ni and registered as UNS R53400, is a near-alpha alloy developed to close the crevice corrosion gap that limits unalloyed titanium in hot chloride brines and weakly reducing acids. Small, controlled additions of molybdenum (0.2-0.4%) and nickel (0.6-0.9%) stabilize the passive film in reducing conditions, giving Grade 12 crevice corrosion resistance that is clearly superior to Grades 2 and 3 and comparable to palladium-bearing grades in many services. The alloy retains the process plasticity and weldability of CP titanium, and it is normally supplied and used in the annealed condition.
ASTM B861 covers seamless and welded titanium tubes for general corrosion-resisting and elevated-temperature service. Grade 12 is a common choice under this specification because it offers a combination of moderate strength, dependable weldability and corrosion performance that pure grades cannot match in chlorides, which is why it appears in chemical plants, desalination, marine systems and power-generation heat exchangers.
Chemical Composition (per ASTM B861, referencing ASTM B265 limits)
| Element | Limit (max %, unless shown as range) |
|---|---|
| Nitrogen, N | 0.03 |
| Carbon, C | 0.08 |
| Hydrogen, H | 0.015 |
| Iron, Fe | 0.30 |
| Oxygen, O | 0.25 |
| Molybdenum, Mo | 0.2-0.4 |
| Nickel, Ni | 0.6-0.9 |
| Titanium, Ti | Balance |
Mechanical Requirements (Annealed, per ASTM B861)
Tensile strength, min: 483 MPa (70 ksi)
Yield strength (0.2% offset), min: 345 MPa (50 ksi)
Elongation in 50 mm, min: 18%
The two values are minimums for the annealed condition. Because Grade 12 is stronger than CP Grades 1-4, designers can use thinner walls for the same pressure rating, which partly offsets the higher alloy cost per kilogram.
Manufacturing Routes and Typical Dimensional Range
Seamless tubes are produced by extrusion or rotary piercing followed by cold rolling or drawing; welded tubes are formed from strip or plate and finished with cold working and annealing as needed. Typical supply range for this grade: outside diameter 21.3-609.6 mm, wall thickness 1.0-10.0 mm, single length up to 6000 mm, wall thickness tolerance +/-12.5% and length tolerance +5 mm. Dimensional and tolerance details always follow the applicable ASTM B861 table for the ordered size.
Applications of Grade 12 Titanium Tube
Chemical processing: piping, heat exchangers and spargers handling hot chlorides, seawater and weakly reducing acids.
Heat exchangers and condensers: resistance to chloride pitting and crevice attack at elevated temperature.
Aerospace components: formed and welded tubular parts where the combination of strength, corrosion resistance and light weight is required.
Marine and offshore: seawater cooling loops, riser instrumentation tubing and ballast systems.
Medical devices: implant-adjacent instrumentation where biocompatibility and corrosion resistance in body fluids matter.
Selection Notes and Common Mistakes
Do not substitute Grade 2 for Grade 12 in hot chloride or crevice-prone service; the crevice corrosion temperature limit of CP titanium is markedly lower, and field failures usually appear as localized attack under gaskets and tube-to-tubesheet joints. If the environment is strongly reducing, compare Grade 12 with Grade 7 (Ti-0.2Pd); palladium grades are more forgiving in severe reducing acids but cost more. Remember that ASTM B861 is the general tube specification, while ASTM B338 covers tube for condensers and heat exchangers with tighter dimensional requirements, and ASME SB861 is the pressure-vessel equivalent. State the required condition, test method and mill certificate (EN 10204 3.1) at enquiry stage to avoid rework.
FAQ
Is Grade 12 titanium tube suitable for seawater?
Yes. Grade 12 resists pitting and crevice corrosion in seawater at elevated temperatures far better than CP grades, and it tolerates the mildly reducing conditions found in stagnant or fouled seawater systems.
What is the difference between Grade 12 and Grade 2 titanium tube?
Grade 2 is unalloyed titanium with excellent general corrosion resistance but a lower crevice corrosion threshold in hot chlorides. Grade 12 adds 0.3% Mo and 0.8% Ni, raising strength to about 483 MPa tensile minimum and extending corrosion resistance into reducing and crevice-prone media.
Can Grade 12 titanium tube be welded?
Yes. Grade 12 has good weldability and is generally used in the annealed condition. Welding should follow qualified procedures with inert gas shielding; filler metal of matching grade is recommended to preserve corrosion performance.
What standards cover Grade 12 titanium tube?
ASTM B861 (seamless and welded tube, general service), ASTM B338 (condenser and heat exchanger tube), ASME SB861 (pressure applications) and ASTM B265 for sheet/plate. Chemistry is specified in ASTM B265 tables referenced by the tube standards.
Why does the title mention aerospace components?
Grade 12's strength-to-weight ratio and formability make it useful in aerospace tubular components such as hydraulic lines and ducting, although its most widespread use remains chemical and marine processing equipment.
What surface conditions are available?
Annealed and pickled is the standard delivery condition; polished, bright annealed and sandblasted surfaces can be specified for heat-exchanger or cosmetic requirements. Surface finish should be stated on the purchase order.







