Hardness of Titanium Tubing: HRB, HRC and HV Values Explained for Real Applications
Jan 26, 2024
What Hardness Actually Measures in Titanium Tube
Hardness is a comparative measure of resistance to local plastic deformation, not a fundamental material property. In titanium tube it responds to three influences that must be separated before any number is used: alloy and interstitial content, especially oxygen and nitrogen; the amount of cold work retained from forming; and the condition of the region tested, whether parent metal, weld or heat affected zone. Two Grade 2 tubes of identical chemistry can therefore differ by tens of Vickers points simply because one was stress relieved and the other was not.
Wall thickness also enters the measurement. A thin wall deflects under the indenter, so the reading reflects the anvil support and the tube geometry as much as the metal itself. Any hardness survey of tubing should therefore state the scale, the load and the standard used.
Typical Hardness Ranges by Grade and Condition
The table lists commonly reported ranges for annealed and cold worked titanium tube. Hardness is not a specified acceptance property for tube in ASTM B338, so these figures are used for process control and comparison, not for acceptance.
| Material and condition | Typical hardness | Practical comment |
|---|---|---|
| Grade 1 and 2, fully annealed | About 120-160 HV, roughly 70-85 HRB | Lowest strength, best formability |
| Grade 3 and 4, fully annealed | About 160-200 HV, roughly 85-95 HRB | Higher oxygen, higher strength |
| Grade 12, annealed | Above the Grade 2 range, typically low on the HRC scale | Molybdenum and nickel raise strength |
| Cold worked tube | Rises with reduction, can exceed the annealed range by 50% or more | Restored by a full anneal |
| Weld fusion and HAZ | Depends on cast structure and gas pick-up | Needs a microhardness traverse, not a single value |
Scales, Conversion and the Ambiguous Range Trap
A statement that hardness is HR30 to HR40 cannot be used in a specification or a technical report, because HR alone is not a scale. Titanium tube is normally reported on Rockwell B (HRB) with a 1/16 inch ball and 100 kgf, on Rockwell C (HRC) with a diamond indenter and 150 kgf for harder conditions, on superficial 15N or 30N for thin wall, and on Vickers (HV) for microhardness traverses and weld zones. Method requirements come from ASTM E18 for Rockwell testing and ASTM E384 for Vickers microindentation.
Use HRB for annealed tubing up to roughly 100 HRB, and superficial scales for thin wall, because the standard Rockwell test can be affected by anvil and wall deflection.
Use HV 0.3 to HV 1 for traverses across a weld, because the zones are narrow and the load must be small enough to stay inside the region of interest.
Treat converted values as estimates. Hardness to tensile conversion tables are approximate and never replace a tensile test to ASTM E8.
Always record the scale, load and standard alongside the value, so the result can be reproduced by another laboratory.
Cold Work, Annealing and Weld Zones
The hardness of a formed tube is largely a record of its thermomechanical history. Cold drawing or pilgering raises dislocation density and hardness roughly in proportion to total reduction; stress relief annealing at 540 to 650 C reduces residual stress with limited softening; a full anneal at 650 to 750 C recrystallises the structure and returns hardness close to the annealed baseline. A reading above the expected range on a supposedly annealed tube therefore points to one of three causes: an insufficient anneal, excess interstitial content from the melt or from processing, or surface contamination with oxygen or iron.
Welds are more complex. The fusion zone is a cast structure that may be slightly softer or harder than the parent metal depending on cooling rate and gas pick-up, while the HAZ often shows the highest values because it combines a transformed structure with elevated interstitials. A useful survey reports three numbers per weld, one for each zone, rather than a single figure for the joint.
Does Hardness Control Service Life?
Not on its own. Higher hardness usually means higher strength and better resistance to mechanical damage, but it also means lower ductility and less tolerance of forming and thermal cycling. For tubing in heat exchangers and process lines, service life is governed mainly by corrosion resistance, wall thickness, cleanliness, weld quality and support spacing. Hardness matters where wear, erosion or mechanical damage is the governing failure mode.
Purchase orders for tube should therefore rely on the properties specified in the applicable standard. ASTM B338 controls tensile strength, yield strength, elongation, flattening and, where applicable, hydrostatic or eddy current testing. Hardness may be added as an agreed process control check, but it should not replace those tests or be used as a pass or fail criterion without a documented basis.
FAQ
Q: Is titanium tubing harder than steel tubing?
Not in absolute terms. Annealed titanium is softer than hardened steels and comparable to or softer than many stainless steels. Its advantages are strength per unit weight and corrosion resistance, not hardness.
Q: What does a reading of 30 to 40 HRC on titanium mean?
It is unusual for annealed tube and suggests a mis-stated scale, a heavily cold worked or contaminated surface, or an indenter and support problem. The measurement should be repeated with a stated scale and standard.
Q: Can hardness verify that a tube is fully annealed?
As process control, yes. A traverse showing uniform values near the agreed baseline indicates that recrystallisation has completed, but tensile testing to ASTM E8 remains the formal acceptance route.
Q: Why does a weld sometimes read higher than the parent metal?
Because the HAZ combines a transformed microstructure with oxygen and nitrogen pick-up, and because residual stress and rapid cooling add further hardening in the narrow transition band.
Q: Does polishing harden the tube surface?
Mechanical polishing can introduce a shallow cold worked layer that slightly raises near-surface microhardness. It does not change the properties of the tube body, but it can affect the first few micrometres of a Vickers traverse.







