GR1 Titanium Pipe vs GR2 Titanium Pipe

May 18, 2026

GR1 titanium pipe and GR2 titanium tube are the two most popular grades of titanium. However, only 10% of total titanium production is considered grade 1. It's important to know the difference if you need to choose an appropriate material for your project.

 

GR1 titanium pipe is pure titanium – a kind of unalloyed titanium with the lowest strength in all kinds of titanium alloys. GR1 titanium tube has high corrosion resistance, good weldability, and high toughness, widely used in industry and medicine.

 

GR2 titanium tube is the most often used titanium grade, utilized in a wide range of applications. This unalloyed titanium grade has superior corrosion resistance and high strength. GR2 also has excellent weldability and fabricability.

ASTM B862 gr1

GR1 Titanium Pipe Key Properties

GR1 titanium pipe offers the following performance characteristics:

Property Description
Corrosion resistance Excellent in various chemical media such as acid and alkali; general corrosion resistance is intermediate between stainless steel and nickel alloys, but superior to both for specific chemical media
High strength Good strength-to-weight ratio
Excellent wear resistance Durable in demanding applications
High heat transfer performance Suitable for GR1 titanium heat exchanger tubes
Good formability GR1 titanium forming/bending is excellent
Light weight Titanium grade 1 density is 4.51 g/cm³

GR1 titanium is widely used in industry and medicine due to its combination of properties.

 

GR2 Titanium Tube Key Properties

GR2 titanium tube (UNS R50400) is the most often used titanium grade, utilized in a wide range of applications. This unalloyed titanium grade has superior corrosion resistance and high strength. GR2 also has excellent weldability and fabricability.

Property Description
Corrosion resistance Superior corrosion resistance in a wide range of environments
High strength Higher strength than GR1 – tensile strength 345 MPa vs 240 MPa
Weldability Excellent weldability
Fabricability Excellent fabricability
Light weight Same titanium grade 1 density – 4.51 g/cm³

GR2 titanium tube is the most commercially pure alloy of all the grades and is often used in aerospace, medical, marine, and chemical processing applications.

 

Chemical Composition Comparison

GR1 titanium chemical composition vs GR2:

Grade N (≤) C (≤) H (≤) Fe (≤) O (≤) Ti
GR1 0.03 0.08 0.015 0.20 0.18 bal
GR2 0.03 0.08 0.015 0.30 0.25 bal

 

Mechanical Properties Comparison

GR1 titanium yield strength vs GR2:

Grade Tensile Strength (≥) Yield Strength (≥) Elongation (≥%)
  ksi MPa ksi MPa
GR1 35 240 20 138 24
GR2 50 345 40 275 20

 

Applications of GR1 Titanium Pipe

What is GR1 titanium pipe used for?

Industry Application
Heat exchangers and condensers GR1 titanium heat exchanger tubes
Offshore aquaculture Seawater piping systems
Chemical industry GR1 titanium for chemical processing – reactors, piping
Electroplating equipment Grade 1 titanium anode/cathode components
Precision instruments High-precision tubing
Environmental protection equipment Corrosion-resistant piping
Navigation / Marine Shipboard systems, seawater cooling
Aerospace Lightweight components
Auto industry Exhaust systems, structural parts
Medical and Sports industry Medical grade 1 titanium – implants, equipment
Electric power industry Cooling system piping
Seawater desalination industry GR1 titanium tube for desalination plants

 

Applications of GR2 Titanium Pipe

GR2 titanium tube is widely used in:

Industry Application
Chemical Chemical processing equipment
Petroleum Oil and gas piping
Light industry General industrial applications
Metallurgy Process equipment
Shipbuilding Marine piping systems
Aerospace Structural components

 

GR1 Titanium Pipe Specifications

Parameter Value
Standard ASTM B338 (Pipe), ASTM B861 (Seamless Tube), ASTM B862 (Welded Tube)
Grade GR1
Titanium grade 1 density 4.51 g/cm³
Melting point 1668°C
Tensile strength (min) 240 MPa (35 ksi)
GR1 titanium yield strength (min) 138 MPa (20 ksi)
Elongation (min) 24%

 

GR2 Titanium Tube Specifications

Parameter Value
Standard ASTM B338 (Pipe), ASTM B861 (Seamless Tube)
Grade GR2
UNS R50400
Titanium grade 2 density 4.51 g/cm³
Tensile strength (min) 345 MPa (50 ksi)
Yield strength (min) 275 MPa (40 ksi)
Elongation (min) 20%

 

GR1 vs GR2 – Which One to Choose?

If you need... Choose...
Maximum formability and ductility GR1 – best for GR1 titanium for deep drawing
Complex shapes and deep drawing GR1 – higher elongation (24% vs 20%)
Higher strength GR2 – 40% stronger than GR1
Structural applications GR2 – higher yield strength (275 MPa vs 138 MPa)
Chemical processing Both – but GR1 preferred for complex equipment shapes
Heat exchangers GR1 – better formability for tube bundles
Marine applications Both – excellent seawater corrosion resistance
Medical implants Both – GR1 for non-load-bearing, GR2 for load-bearing

 

Equivalent Standards

Standard GR1 GR2
UNS R50250 R50400
W. Nr. 3.7025 3.7035
ASTM Pipe B338 Grade 1 B338 Grade 2
ASTM Seamless Tube B861 Grade 1 B861 Grade 2
Medical ASTM F67 Grade 1 ASTM F67 Grade 2
ISO 5832-2 Grade 1 5832-2 Grade 2
Chinese (GB/T) TA1 TA2

 

Physical Properties Comparison

Property GR1 GR2
Density (g/cm³) 4.51 4.51
Melting point (°C) 1668 1668
Thermal conductivity (W/m·K) ~17 ~17
Coefficient of thermal expansion (×10⁻⁶/K) 8.6 8.6
Elastic modulus (GPa) ~105 ~105

 

FAQ

Q1: What is the difference between GR1 and GR2 titanium pipe?
A: The difference between pure titanium GR1 and GR2 is primarily oxygen and iron content. GR1 has 0.18% oxygen max and 0.20% iron max. GR2 has 0.25% oxygen max and 0.30% iron max. This gives GR1 higher ductility (24% vs 20% elongation) and lower strength (138 MPa vs 275 MPa yield strength). Titanium grade 1 vs grade 2 selection depends on whether formability or strength is the priority.

 

Q2: Which is stronger – GR1 or GR2?
A: GR2 is significantly stronger. GR2 has tensile strength of 345 MPa (50 ksi) and yield strength of 275 MPa (40 ksi). GR1 has tensile strength of 240 MPa (35 ksi) and GR1 titanium yield strength of 138 MPa (20 ksi). GR2 is approximately 40% stronger than GR1.

 

Q3: Which is more ductile – GR1 or GR2?
A: GR1 is more ductile. GR1 has minimum elongation of 24%, while GR2 has 20%. This higher ductility makes GR1 titanium for deep drawing the preferred choice for complex forming operations. GR1 titanium forming/bending is excellent.

 

Q4: What is the UNS number for GR1 titanium tube?
A: The UNS number for GR1 titanium tube is R50250. GR2 has UNS R50400. ASTM B861 grade 1 titanium tube uses R50250. ASTM B338 grade 1 titanium pipe also uses R50250.

 

Q5: What are the applications of GR1 titanium pipe?
A: GR1 titanium pipe is used in heat exchangers and condensers, offshore aquaculture, chemical industry, electroplating equipment, precision instruments, environmental protection, navigation, aerospace, auto industry, medical and sports industry, electric power industry, and seawater desalination. GR1 titanium heat exchanger tubes are particularly common.

 

Q6: What are the applications of GR2 titanium tube?
A: GR2 titanium tube is widely used in chemical, petroleum, light industry, metallurgy, shipbuilding, aerospace, and other fields. GR2 is the most commercially pure alloy and is often used in aerospace, medical, marine, and chemical processing applications.

 

Q7: Is GR1 titanium pipe suitable for heat exchangers?
A: Yes, GR1 titanium heat exchanger tubes are widely used. GR1 has high heat transfer performance and excellent corrosion resistance in seawater and chemical environments. GR1 titanium for chemical processing includes heat exchanger applications.

 

Q8: Is GR1 titanium pipe suitable for medical applications?
A: Yes, medical grade 1 titanium conforming to ASTM F67 grade 1 is used for implants and medical devices. GR1 titanium is biocompatible and offers excellent corrosion resistance. GR1 titanium is used in medical and sports industry applications.

 

Q9: Is GR1 titanium pipe suitable for electroplating equipment?
A: Yes, grade 1 titanium anode/cathode components are used in electroplating equipment. GR1 titanium MMO anode (mixed metal oxide coated) is a standard substrate for electrochemical applications. GR1 titanium offers excellent corrosion resistance in electroplating baths.

 

Q10: What is the chemical composition difference between GR1 and GR2?
A: GR1 titanium chemical composition – N ≤0.03%, C ≤0.08%, H ≤0.015%, Fe ≤0.20%, O ≤0.18%, Ti balance. GR2 has Fe ≤0.30% and O ≤0.25%. GR1 has tighter controls on both iron and oxygen, resulting in higher purity and ductility.

 

Q11: How to weld GR1 titanium pipe?
A: How to weld GR1 titanium – both GR1 and GR2 have excellent weldability. Use GTAW (TIG) with ERTi-1 filler for GR1 and ERTi-2 for GR2. Proper argon shielding on both sides is critical. No preheat or post-weld heat treatment is required for most applications.

 

Q12: What is the yield strength of GR1 titanium pipe?
A: The minimum GR1 titanium yield strength is 138 MPa (20 ksi) per ASTM B265. Some specifications show 170 MPa. GR1 has the lowest yield strength among CP grades, which directly enables its excellent formability for GR1 titanium for deep drawing.

 

Q13: What is the elongation of GR1 titanium tube?
A: GR1 titanium tube has minimum elongation of 24%. GR2 has 20%. The higher elongation of GR1 makes it more suitable for GR1 titanium forming/bending and GR1 titanium for deep drawing operations where complex shapes are required.

 

Q14: Is GR1 titanium pipe suitable for marine applications?
A: Yes, GR1 titanium pipe is widely used in navigation and offshore aquaculture. GR1 titanium has excellent corrosion resistance in seawater. GR1 titanium heat exchanger tubes and seawater piping systems are common in marine applications.

 

Q15: What is the density of GR1 titanium pipe?
A: Titanium grade 1 density is 4.51 g/cm³ – the same for GR2. Both grades have identical physical properties including melting point (1668°C), thermal conductivity (~17 W/m·K), and coefficient of thermal expansion (8.6 × 10⁻⁶/K).