Superplastic Forming Of Titanium Alloy Sheets
Aug 11, 2025
Superplastic forming of titanium alloy sheets can be roughly divided into the following three methods:
(1) Vacuum forming;
(2) Air pressure forming (blow molding);
(3) Compression molding (coupling molding).
The first two methods are commonly used methods for forming plastic (or glass) products. Titanium sheet superplastic forming belongs to viscous or semi-viscous flow deformation, so low pressure forming can be used. Air pressure forming can also be combined with vacuum forming.
1. Vacuum forming method
Vacuum forming method can be divided into two types: punch method and die method.
The punch method is a forming method in which the heated raw material is adsorbed on a punch with the inner shape of the part. It is used to form parts that require high inner dimensional accuracy. The die method is a forming method in which the heated raw material is adsorbed on a die with the outer shape of the part. It is used to form parts that require high outer dimensional accuracy. Generally speaking, the former is used for forming deeper containers, and the latter is used for forming shallower containers. Vacuum forming is also a form of pneumatic forming, but the forming pressure can only be one atmosphere. Therefore, for titanium sheets, it can only form thin, simple-shaped parts with gentle curvatures, and is unsuitable for forming thicker, more complex shapes, or parts with significant deformation.




2. Pneumatic Forming (Blow Molding)
This is a special bulging process.
Traditional bulging processes are performed using mechanical, hydraulic, or explosive bulging methods. These methods use relatively high pressures and energies, and due to the plasticity of the material, the deformation is generally limited. Blow molding, on the other hand, achieves large deformations with low energy and pressure, a sheet metal forming technology that differs from traditional processes. Because the metal is free during deformation, almost all of the energy is consumed in the deformation work, resulting in minimal friction losses (in free blow molding, there is no friction loss). This fundamentally distinguishes it from other stamping processes.
Blow molding can be divided into free blow molding and mold blow molding. The characteristic of mold blow molding is half mold forming. Similar to vacuum forming, it is also divided into two types: male mold forming and female mold forming. The difference is that the forming pressure can be greater than one atmosphere, and the pressure can be adjusted through the air source system, so parts with complex shapes and large curvature changes can be manufactured. (1) Free blow molding method This is the simplest type of blow molding. Its characteristic is that no mold is used, and the typical blown parts are spherical parts. (2) Male mold forming method This method is to form a closed pressure space on the outside of the titanium plate blank. After the titanium plate is heated to the superplastic temperature, under the action of the compressed gas pressure, the blank undergoes superplastic deformation and gradually approaches the mold surface until it is completely fitted with the mold, making a part identical to the mold surface. The inner surface of the formed part has high dimensional accuracy, accurate shape, large depth-to-width ratio, and is easy to process. However, demolding is difficult and the raw materials are more expensive. The bottom of the part formed by this method is thicker than the surrounding area. (3) Concave Die Forming Method
Unlike the convex die forming method, a closed pressure space is formed inside the titanium sheet blank during the forming process. The outer surface dimensions of the formed part are highly accurate, the shape is accurate, the part is easier to demold, and the raw material is less used. However, the depth and width are relatively small, and mold processing is also more difficult. The bottom of the part formed by this method is thinner than the surrounding area.
3. Compression Molding Method
A coupling mold is used. Unlike ordinary compression molding, the temperature is high and the molding speed is much slower.
Because it is difficult to manufacture a metal coupling mold that can withstand the superplastic temperature of titanium sheet, and the matching accuracy is difficult to ensure (especially for molds with complex shapes), superplastic forming of titanium sheet is rarely used.
The company boasts leading domestic titanium processing production lines, including:
German-imported precision titanium tube production line (annual production capacity: 30,000 tons);
Japanese-technology titanium foil rolling line (thinnest to 6μm);
Fully automated titanium rod continuous extrusion line;
Intelligent titanium plate and strip finishing mill;
The MES system enables digital control and management of the entire production process, achieving product dimensional accuracy of ±0.01μm.








